This is the XD204 Data logger Module/Shield for Arduino that can be used to store the values that come from a sensor or the data received serially on a SD Card. It supports upto 1 GB SD card memory on ...
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on ...
This DC geared motor runs at 150rpm. Used widely in numerous robotic applications.
It requires 5V drawing 300mA of current. They fit perfectly with our robotic wheels. ...
This DC geared motor runs at 60rpm. Used widely in numerous robotic applications.
It requires 5V drawing 300mA of current. They fit perfectly with the our robotic wheels. ...
With this DC-DC Step Up Module,You can DIY an output adjustable vehicle power supply, connect the 12V input, and output could be 14-35V(adjustable freely), However, the output voltage can not be less than the input voltage. Can also be used as ...
The industry standard in high performance connectors. The Deans T-Plug connectors actually have less resistance, including the solder joints, than an equivalent length piece of 12 gauge wire. These connectors are made from Nylon, making them very tough and difficult ...
This is a high grade Desoldering Pump that can be used in order to remove components from a PCB Circuit Board. It can also be used for removing excess solder. All you have to do is , heat up the ...
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins ...
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins ...
Digispark is an ATtiny85 based microcontroller ...
Digispark is an ATtiny85 based microcontroller development board come with USB interface. Coding is similar to Arduino, and it use the familiar Arduino IDE for development. ...
This is a Digital Light Sensor Module that can be used to detect the light intensity of the surroundings. It Can detect ambient brightness and intensity (compare with the photo resistor, better direction, can perceive the light source of the fixed ...
This is a digital multimeter used to measure various quantities like Voltage, Current, Circuit Continuity etc. in an electronic or electrical circuit. The multimeter can also be used to detect consistency of PNP or NPN Transistors. ...
This is a simple, very common rectifier diode. Often used for reverse voltage protection, the 1N4001 is a staple for many power, DC to DC step up, and breadboard projects. 1N4001 is rated for up to 1A/50V. ...
This is a DIY (Do-it-Yourself) Quadcopter Kit that contains all the components which are required to assemble and operate a Quadrotor. This is an all-in-one solution for Drone Building enthusiasts . ...
This is a DIY (Do-it-Yourself) Hexacopter Kit that contains all the components which are required to assemble and operate a Hexarotor. This is an all-in-one solution for Drone Building enthusiasts . ...
This is a DIY (Do-it-Yourself) Hexacopter Kit that contains all the components which are required to assemble and operate a Hexarotor. This is an all-in-one solution for Drone Building enthusiasts . ...
Prusa i3 is a proven design with tens of thousands users all around the planet. Now you have a great opportunity to buy one directly from the author Josef Průša and support it's further development. All parts of this 3D ...
A Real Time Clock Module with battery backup using the easy to use DS1302 chip. The DS1302 chip uses a simple serial interface (see datasheet) and example code is available for Arduino, Raspberry Pi and many others. ...
Probe using original DS18B20 temperature sensor ...
Probe using original DS18B20 temperature sensor chip. The high-quality stainless steel pipe encapsulation makes it waterproof, moisture-proof and anti-rust.The thermal detection probe can be easily interfaced with micro controllers to develop temperature based projects and devices. ...
DS3231 is a low-cost, extremely accurate I2C real-time clock (RTC), with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. The device incorporates a battery input, disconnect the main power supply and maintains accurate timekeeping. ...
An infrared sensor is an electronic instrument that is used to sense certain characteristics of its surroundings by either emitting or detecting infra red radiation. It is also capable of measuring heat of an object and detecting motion. ...
This is DYS 30A Electronic Speed Controller With SimonK Firmware MB30030. The ESC is most suitable for Multirotors ,RC Planes , Hovercrafts and any other RC Models ...
This is the DYS Outrunner Brushless DC Motor rated at 1100KV for Quadrotors and Multicopters. The motors are suitable for mid range Quadcopters like F450 or F550 and are compatible with 08x4.5 Propellers and 2-3S Lipo Batteries ...
This is a 9g, Analog Servo ideal for Hobby Robotics and RC Applications. Its light weight and compatibility with Arduino makes it very user-friendly and easy to operate.
...
This is a DIY (Do-it-Yourself) Economy Quadcopter ...
This is a DIY (Do-it-Yourself) Economy Quadcopter Kit that contains all the components which are required to assemble and operate a Quadrotor. This is an all-in-one solution for Drone Building enthusiasts. ...
This RFID module is desgined based on MFRC522. It is a highly integrated reader/writer for contactless communication at 13.56MHz. It supports ISO 14443A/MIFARE mode and MIFARE Classic (e.g. MIFARE Standard) products ...
